 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| DS1820 DS1820 1-WireTM Digital Thermometer FEATURES PIN ASSIGNMENT DALLAS DALLAS DS2434 DS1820 1 2 3 * Unique 1-WireTM interface requires only one port pin for communication * Multidrop capability simplifies distributed temperature sensing applications * Requires no external components * Can be powered from data line * Zero standby power required * Measures temperatures from -55C to +125C in 0.5C increments. Fahrenheit equivalent is -67F to +257F in 0.9F increments BOTTOM VIEW 1 23 * Temperature is read as a 9-bit digital value. * Converts temperature to digital word in 200 ms (typ.) * User-definable, tings nonvolatile temperature alarm set- DS1820 PR35 PACKAGE See Mech. Drawings Section GND DQ VDD NC NC NC NC NC NC VDD DQ 1 2 3 4 5 6 7 8 16 15 14 13 12 11 10 9 NC NC NC NC NC NC NC GND DS1820S 16-PIN SSOP See Mech. Drawings Section * Alarm search command identifies and addresses devices whose temperature is outside of programmed limits (temperature alarm condition) systems, consumer products, thermometers, or any thermally sensitive system PIN DESCRIPTION GND DQ VDD NC - - - - Ground Data In/Out Optional VDD No Connect * Applications include thermostatic controls, industrial DESCRIPTION The DS1820 Digital Thermometer provides 9-bit temperature readings which indicate the temperature of the device. Information is sent to/from the DS1820 over a 1-Wire interface, so that only one wire (and ground) needs to be connected from a central microprocessor to a DS1820. Power for reading, writing, and performing temperature conversions can be derived from the data line itself with no need for an external power source. Because each DS1820 contains a unique silicon serial number, multiple DS1820s can exist on the same 1-Wire bus. This allows for placing temperature sensors in many different places. Applications where this feature is useful include HVAC environmental controls, sensing temperatures inside buildings, equipment or machinery, and in process monitoring and control. 030598 1/27 DS1820 DETAILED PIN DESCRIPTION PIN 16-PIN SSOP 9 8 7 PIN PR35 1 2 3 SYMBOL GND DQ VDD Ground. Data Input/Output pin. For 1-Wire operation: Open drain. (See "Parasite Power" section.) Optional VDD pin. See "Parasite Power" section for details of connection. DESCRIPTION DS1820S (16-pin SSOP): All pins not specified in this table are not to be connected. OVERVIEW The block diagram of Figure 1 shows the major components of the DS1820. The DS1820 has three main data components: 1) 64-bit lasered ROM, 2) temperature sensor, and 3) nonvolatile temperature alarm triggers TH and TL. The device derives its power from the 1-Wire communication line by storing energy on an internal capacitor during periods of time when the signal line is high and continues to operate off this power source during the low times of the 1-Wire line until it returns high to replenish the parasite (capacitor) supply. As an alternative, the DS1820 may also be powered from an external 5 volts supply. Communication to the DS1820 is via a 1-Wire port. With the 1-Wire port, the memory and control functions will not be available before the ROM function protocol has been established. The master must first provide one of five ROM function commands: 1) Read ROM, 2) Match ROM, 3) Search ROM, 4) Skip ROM, or 5) Alarm Search. These commands operate on the 64-bit lasered ROM portion of each device and can single out a specific device if many are present on the 1-Wire line as well as indicate to the Bus Master how many and what types of devices are present. After a ROM function sequence has been successfully executed, the memory and control functions are accessible and the master may then provide any one of the six memory and control function commands. One control function command instructs the DS1820 to perform a temperature measurement. The result of this measurement will be placed in the DS1820's scratchpad memory, and may be read by issuing a memory function command which reads the contents of the scratchpad memory. The temperature alarm triggers TH and TL consist of one byte EEPROM each. If the alarm search command is not applied to the DS1820, these registers may be used as general purpose user memory. Writing TH and TL is done using a memory function command. Read access to these registers is through the scratchpad. All data is read and written least significant bit first. DS1820 BLOCK DIAGRAM Figure 1 MEMORY AND CONTROL LOGIC DQ 64-BIT ROM AND 1-WIRE PORT TEMPERATURE SENSOR INTERNAL VDD SCRATCHPAD HIGH TEMPERATURE TRIGGER, TH LOW TEMPERATURE TRIGGER, TL VDD POWER SUPPLY SENSE 8-BIT CRC GENERATOR 030598 2/27 DS1820 PARASITE POWER The block diagram (Figure 1) shows the parasite powered circuitry. This circuitry "steals" power whenever the I/O or VDD pins are high. I/O will provide sufficient power as long as the specified timing and voltage requirements are met (see the section titled "1-Wire Bus System"). The advantages of parasite power are two-fold: 1) by parasiting off this pin, no local power source is needed for remote sensing of temperature, and 2) the ROM may be read in absence of normal power. In order for the DS1820 to be able to perform accurate temperature conversions, sufficient power must be provided over the I/O line when a temperature conversion is taking place. Since the operating current of the DS1820 is up to 1 mA, the I/O line will not have sufficient drive due to the 5K pull-up resistor. This problem is particularly acute if several DS1820's are on the same I/O and attempting to convert simultaneously. There are two ways to assure that the DS1820 has sufficient supply current during its active conversion cycle. The first is to provide a strong pull-up on the I/O line whenever temperature conversions or copies to the E2 memory are taking place. This may be accomplished by using a MOSFET to pull the I/O line directly to the power supply as shown in Figure 2. The I/O line must be switched over to the strong pull-up within 10 s maximum after issuing any protocol that involves copying to the E2 memory or initiates temperature conversions. When using the parasite power mode, the VDD pin must be tied to ground. Another method of supplying current to the DS1820 is through the use of an external power supply tied to the VDD pin, as shown in Figure 3. The advantage to this is that the strong pull-up is not required on the I/O line, and the bus master need not be tied up holding that line high during temperature conversions. This allows other data traffic on the 1-Wire bus during the conversion time. In addition, any number of DS1820's may be placed on the 1-Wire bus, and if they all use external power, they may all simultaneously perform temperature conversions by issuing the Skip ROM command and then issuing the Convert T command. Note that as long as the external power supply is active, the GND pin may not be floating. The use of parasite power is not recommended above 100C, since it may not be able to sustain communications given the higher leakage currents the DS1820 exhibits at these temperatures. For applications in which such temperatures are likely, it is strongly recommended that VDD be applied to the DS1820. For situations where the bus master does not know whether the DS1820's on the bus are parasite powered or supplied with external VDD, a provision is made in the DS1820 to signal the power supply scheme used. The bus master can determine if any DS1820's are on the bus which require the strong pull-up by sending a Skip ROM protocol, then issuing the read power supply command. After this command is issued, the master then issues read time slots. The DS1820 will send back "0" on the 1-Wire bus if it is parasite powered; it will send back a "1" if it is powered from the VDD pin. If the master receives a "0", it knows that it must supply the strong pull-up on the I/O line during temperature conversions. See "Memory Command Functions" section for more detail on this command protocol. STRONG PULL-UP FOR SUPPLYING DS1820 DURING TEMPERATURE CONVERSION Figure 2 +5V DS1820 +5V GND 4.7K VDD P I/O 030598 3/27 DS1820 USING VDD TO SUPPLY TEMPERATURE CONVERSION CURRENT Figure 3 TO OTHER 1-WIRE DEVICES DS1820 +5V 4.7K VDD P I/O EXTERNAL +5V SUPPLY OPERATION - MEASURING TEMPERATURE The DS1820 measures temperature through the use of an on-board proprietary temperature measurement technique. A block diagram of the temperature measurement circuitry is shown in Figure 4. The DS1820 measures temperature by counting the number of clock cycles that an oscillator with a low temperature coefficient goes through during a gate period determined by a high temperature coefficient oscillator. The counter is preset with a base count that corresponds to -55C. If the counter reaches zero before the gate period is over, the temperature register, which is also preset to the -55C value, is incremented, indicating that the temperature is higher than -55C. At the same time, the counter is then preset with a value determined by the slope accumulator circuitry. This circuitry is needed to compensate for the parabolic behavior of the oscillators over temperature. The counter is then clocked again until it reaches zero. If the gate period is still not finished, then this process repeats. The slope accumulator is used to compensate for the non-linear behavior of the oscillators over temperature, yielding a high resolution temperature measurement. This is done by changing the number of counts necessary for the counter to go through for each incremental degree in temperature. To obtain the desired resolution, therefore, both the value of the counter and the number of counts per degree C (the value of the slope accumulator) at a given temperature must be known. Internally, this calculation is done inside the DS1820 to provide 0.5C resolution. The temperature reading is provided in a 16-bit, sign-extended two's complement reading. Table 1 describes the exact relationship of output data to measured temperature. The data is transmitted serially over the 1-Wire interface. The DS1820 can measure temperature over the range of -55C to +125C in 0.5C increments. For Fahrenheit usage, a lookup table or conversion factor must be used. Note that temperature is represented in the DS1820 in terms of a 1/2C LSB, yielding the following 9-bit format: MSB 1 1 1 0 0 1 1 1 LSB 0 = -25C The most significant (sign) bit is duplicated into all of the bits in the upper MSB of the two-byte temperature register in memory. This "sign-extension" yields the 16-bit temperature readings as shown in Table 1. Higher resolutions may be obtained by the following procedure. First, read the temperature, and truncate the 0.5C bit (the LSB) from the read value. This value is TEMP_READ. The value left in the counter may then be read. This value is the count remaining (COUNT_REMAIN) after the gate period has ceased. The last value needed is the number of counts per degree C (COUNT_PER_C) at that temperature. The actual temperature may be then be calculated by the user using the following: TEMPERATURE = TEMP_READ - 0.25 ) (COUNT_PER_C - COUNT_REMAIN) COUNT_PER_C 030598 4/27 DS1820 TEMPERATURE MEASURING CIRCUITRY Figure 4 SLOPE ACCUMULATOR PRESET COMPARE LOW TEMPERATURE COEFFICIENT OSCILLATOR COUNTER PRESET SET/CLEAR LSB INC =0 TEMPERATURE REGISTER HIGH TEMPERATURE COEFFICIENT OSCILLATOR COUNTER =0 STOP TEMPERATURE/DATA RELATIONSHIPS Table 1 TEMPERATURE +125C +25C +1 /2C DIGITAL OUTPUT (Binary) 00000000 11111010 00000000 00110010 00000000 00000001 00000000 00000000 11111111 11111111 11111111 11001110 11111111 10010010 DIGITAL OUTPUT (Hex) 00FA 0032h 0001h 0000h FFFFh FFCEh FF92h +0C -1/2C -25C -55C OPERATION - ALARM SIGNALING After the DS1820 has performed a temperature conversion, the temperature value is compared to the trigger values stored in TH and TL. Since these registers are 8-bit only, the 0.5C bit is ignored for comparison. The most significant bit of TH or TL directly corresponds to the sign bit of the 16-bit temperature register. If the result of a temperature measurement is higher than TH or lower than TL, an alarm flag inside the device is set. This flag is updated with every temperature measurement. As long as the alarm flag is set, the DS1820 will respond to the alarm search command. This allows many DS1820s to be connected in parallel doing simultaneous temperature measurements. If somewhere the temperature exceeds the limits, the alarming device(s) can be identified and read immediately without having to read non-alarming devices. 030598 5/27 DS1820 64-BIT LASERED ROM Each DS1820 contains a unique ROM code that is 64-bits long. The first eight bits are a 1-Wire family code (DS1820 code is 10h). The next 48 bits are a unique serial number. The last eight bits are a CRC of the first 56 bits. (See Figure 5.) The 64-bit ROM and ROM Function Control section allow the DS1820 to operate as a 1-Wire device and follow the 1-Wire protocol detailed in the section "1-Wire Bus System". The functions required to control sections of the DS1820 are not accessible until the ROM function protocol has been satisfied. This protocol is described in the ROM function protocol flowchart (Figure 6). The 1-Wire bus master must first provide one of five ROM function commands: 1) Read ROM, 2) Match ROM, 3) Search ROM, 4) Skip ROM, or 5) Alarm Search. After a ROM functions sequence has been successfully executed, the functions specific to the DS1820 are accessible and the bus master may then provide and one of the six memory and control function commands. vides this value to the bus master to validate the transfer of data bytes. In each case where a CRC is used for data transfer validation, the bus master must calculate a CRC value using the polynomial function given above and compare the calculated value to either the 8-bit CRC value stored in the 64-bit ROM portion of the DS1820 (for ROM reads) or the 8-bit CRC value computed within the DS1820 (which is read as a ninth byte when the scratchpad is read). The comparison of CRC values and decision to continue with an operation are determined entirely by the bus master. There is no circuitry inside the DS1820 that prevents a command sequence from proceeding if the CRC stored in or calculated by the DS1820 does not match the value generated by the bus master. The 1-Wire CRC can be generated using a polynomial generator consisting of a shift register and XOR gates as shown in Figure 7. Additional information about the Dallas 1-Wire Cyclic Redundancy Check is available in Application Note 27 entitled "Understanding and Using Cyclic Redundancy Checks with Dallas Semiconductor Touch Memory Products". The shift register bits are initialized to zero. Then starting with the least significant bit of the family code, one bit at a time is shifted in. After the 8th bit of the family code has been entered, then the serial number is entered. After the 48th bit of the serial number has been entered, the shift register contains the CRC value. Shifting in the eight bits of CRC should return the shift register to all zeros. CRC GENERATION The DS1820 has an 8-bit CRC stored in the most significant byte of the 64-bit ROM. The bus master can compute a CRC value from the first 56-bits of the 64-bit ROM and compare it to the value stored within the DS1820 to determine if the ROM data has been received error-free by the bus master. The equivalent polynomial function of this CRC is: CRC = X8 + X5 + X4 + 1 The DS1820 also generates an 8-bit CRC value using the same polynomial function shown above and pro- 64-BIT LASERED ROM Figure 5 8-BIT CRC CODE MSB LSB 48-BIT SERIAL NUMBER MSB LSB 8-BIT FAMILY CODE (10h) MSB LSB 030598 6/27 DS1820 ROM FUNCTIONS FLOW CHART Figure 6 MASTER TX RESET PULSE DS1820 TX PRESENCE PULSE MASTER TX ROM FUNCTION COMMAND 33h READ ROM COMMAND Y N 55h MATCH ROM COMMAND Y N F0h SEARCH ROM COMMAND Y N ECh ALARM SEARCH COMMAND Y ALARM CONDITION ? Y N CCh SKIP ROM COMMAND Y N N DS1820 TX FAMILY CODE 1 BYTE MASTER TX BIT 0 DS1820 TX BIT 0 DS1820 TX BIT 0 MASTER TX BIT 0 DS1820 TX SERIAL NUMBER 6 BYTES BIT 0 MATCH? Y N N BIT 0 MATCH? Y DS1820 TX BIT 1 DS1820 TX CRC BYTE MASTER TX BIT 1 DS1820 TX BIT 1 MASTER TX BIT 1 BIT 1 MATCH? Y N N BIT 1 MATCH? Y DS1820 TX BIT 63 MASTER TX BIT 63 DS1820 TX BIT 63 MASTER TX BIT 63 BIT 63 MATCH? Y N N BIT 63 MATCH? Y MASTER TX MEMORY OR CONTROL FUNCTION COMMAND 030598 7/27 DS1820 1-WIRE CRC CODE Figure 7 INPUT XOR (MSB) XOR (LSB) XOR MEMORY The DS1820's memory is organized as shown in Figure 8. The memory consists of a scratchpad RAM and a nonvolatile, electrically erasable (E2) RAM, which stores the high and low temperature triggers TH and TL. The scratchpad helps insure data integrity when communicating over the 1-Wire bus. Data is first written to the scratchpad where it can be read back. After the data has been verified, a copy scratchpad command will transfer the data to the nonvolatile (E2) RAM. This process insures data integrity when modifying the memory. The scratchpad is organized as eight bytes of memory. The first two bytes contain the measured temperature information. The third and fourth bytes are volatile copies of TH and TL and are refreshed with every power-on reset. The next two bytes are not used; upon reading back, however, they will appear as all logic 1's. The seventh and eighth bytes are count registers, which may be used in obtaining higher temperature resolution (see "Operation-measuring Temperature" section). There is a ninth byte which may be read with a Read Scratchpad command. This byte contains a cyclic redundancy check (CRC) byte which is the CRC over all of the eight previous bytes. This CRC is implemented in the fashion described in the section titled "CRC Generation". DS1820 MEMORY MAP Figure 8 SCRATCHPAD TEMPERATURE LSB TEMPERATURE MSB TH/USER BYTE 1 TL/USER BYTE 2 RESERVED RESERVED COUNT REMAIN COUNT PER C E2 RAM BYTE 0 1 2 3 4 5 6 7 TH/USER BYTE 1 TL/USER BYTE 2 CRC 8 030598 8/27 DS1820 1-WIRE BUS SYSTEM The 1-Wire bus is a system which has a single bus master and one or more slaves. The DS1820 behaves as a slave. The discussion of this bus system is broken down into three topics: hardware configuration, transaction sequence, and 1-Wire signaling (signal types and timing). at the appropriate time. To facilitate this, each device attached to the 1-Wire bus must have open drain or 3-state outputs. The 1-Wire port of the DS1820 (I/O pin) is open drain with an internal circuit equivalent to that shown in Figure 9. A multidrop bus consists of a 1-Wire bus with multiple slaves attached. The 1-Wire bus requires a pullup resistor of approximately 5K. HARDWARE CONFIGURATION The 1-Wire bus has only a single line by definition; it is important that each device on the bus be able to drive it HARDWARE CONFIGURATION Figure 9 +5V BUS MASTER 4.7K RX RX DS1820 1-WIRE PORT 5 A Typ. TX 1OO OHM MOSFET RX = RECEIVE TX = TRANSMIT TX The idle state for the 1-Wire bus is high. If for any reason a transaction needs to be suspended, the bus MUST be left in the idle state if the transaction is to resume. Infinite recovery time can occur between bits so long as the 1-Wire bus is in the inactive (high) state during the recovery period. If this does not occur and the bus is left low for more than 480 s, all components on the bus will be reset. INITIALIZATION All transactions on the 1-Wire bus begin with an initialization sequence. The initialization sequence consists of a reset pulse transmitted by the bus master followed by presence pulse(s) transmitted by the slave(s). The presence pulse lets the bus master know that the DS1820 is on the bus and is ready to operate. For more details, see the "1-Wire Signaling" section. TRANSACTION SEQUENCE The protocol for accessing the DS1820 via the 1-Wire port is as follows: ROM FUNCTION COMMANDS Once the bus master has detected a presence, it can issue one of the five ROM function commands. All ROM function commands are 8-bits long. A list of these commands follows (refer to flowchart in Figure 6): * Initialization * ROM Function Command * Memory Function Command * Transaction/Data 030598 9/27 DS1820 Read ROM [33h] This command allows the bus master to read the DS1820's 8-bit family code, unique 48-bit serial number, and 8-bit CRC. This command can only be used if there is a single DS1820 on the bus. If more than one slave is present on the bus, a data collision will occur when all slaves try to transmit at the same time (open drain will produce a wired AND result). conversion should be done to validate any alarm conditions. Example of a ROM Search The ROM search process is the repetition of a simple 3-step routine: read a bit, read the complement of the bit, then write the desired value of that bit. The bus master performs this simple, 3-step routine on each bit of the ROM. After one complete pass, the bus master knows the contents of the ROM in one device. The remaining number of devices and their ROM codes may be identified by additional passes. The following example of the ROM search process assumes four different devices are connected to the same 1-Wire bus. The ROM data of the four devices is as shown: ROM1 ROM2 ROM3 ROM4 00110101... 10101010... 11110101... 00010001... Match ROM [55h] The match ROM command, followed by a 64-bit ROM sequence, allows the bus master to address a specific DS1820 on a multidrop bus. Only the DS1820 that exactly matches the 64-bit ROM sequence will respond to the following memory function command. All slaves that do not match the 64-bit ROM sequence will wait for a reset pulse. This command can be used with a single or multiple devices on the bus. Skip ROM [CCh] This command can save time in a single drop bus system by allowing the bus master to access the memory functions without providing the 64-bit ROM code. If more than one slave is present on the bus and a read command is issued following the Skip ROM command, data collision will occur on the bus as multiple slaves transmit simultaneously (open drain pulldowns will produce a wired AND result). The search process is as follows: 1. The bus master begins the initialization sequence by issuing a reset pulse. The slave devices respond by issuing simultaneous presence pulses. 2. The bus master will then issue the Search ROM command on the 1-Wire bus. 3. The bus master reads a bit from the 1-Wire bus. Each device will respond by placing the value of the first bit of their respective ROM data onto the 1-Wire bus. ROM1 and ROM4 will place a 0 onto the 1-Wire bus, i.e., pull it low. ROM2 and ROM3 will place a 1 onto the 1-Wire bus by allowing the line to stay high. The result is the logical AND of all devices on the line, therefore the bus master sees a 0. The bus master reads another bit. Since the Search ROM data command is being executed, all of the devices on the 1-Wire bus respond to this second read by placing the complement of the first bit of their respective ROM data onto the 1-Wire bus. ROM1 and ROM4 will place a 1 onto the 1-Wire, allowing the line to stay high. ROM2 and ROM3 will place a 0 onto the 1-Wire, thus it will be pulled low. The bus master again observes a 0 for the complement of the first ROM data bit. The bus master has determined that there are some devices on the 1-Wire bus that have a 0 in the first position and others that have a 1. Search ROM [F0h] When a system is initially brought up, the bus master might not know the number of devices on the 1-Wire bus or their 64-bit ROM codes. The search ROM command allows the bus master to use a process of elimination to identify the 64-bit ROM codes of all slave devices on the bus. Alarm Search [ECh] The flowchart of this command is identical to the Search ROM command. However, the DS1820 will respond to this command only if an alarm condition has been encountered at the last temperature measurement. An alarm condition is defined as a temperature higher than TH or lower than TL. The alarm condition remains set as long as the DS1820 is powered up, or until another temperature measurement reveals a non-alarming value. For alarming, the trigger values stored in EEPROM are taken into account. If an alarm condition exists and the TH or TL settings are changed, another temperature 030598 10/27 DS1820 The data obtained from the two reads of the 3-step routine have the following interpretations: 00 01 10 11 There are still devices attached which have conflicting bits in this position. All devices still coupled have a 0-bit in this bit position. All devices still coupled have a 1-bit in this bit position. There are no devices attached to the 1-Wire bus. 15. The bus master executes two read time slots and receives two zeros. 16. The bus master writes a 0-bit. This decouples ROM3, and leaving only ROM2. 17. The bus master reads the remainder of the ROM bits for ROM2 and communicates to the underlying logic if desired. This completes the third ROM search pass, in which another of the ROMs was found. 18. The bus master starts a new ROM search by repeating steps 13 through 15. 19. The bus master writes a 1-bit. This decouples ROM2, leaving only ROM3. 20. The bus master reads the remainder of the ROM bits for ROM3 and communicates to the underlying logic if desired. This completes the fourth ROM search pass, in which another of the ROMs was found. 4. The bus master writes a 0. This deselects ROM2 and ROM3 for the remainder of this search pass, leaving only ROM1 and ROM4 connected to the 1-Wire bus. 5. The bus master performs two more reads and receives a 0-bit followed by a 1-bit. This indicates that all devices still coupled to the bus have 0's as their second ROM data bit. 6. The bus master then writes a 0 to keep both ROM1 and ROM4 coupled. 7. The bus master executes two reads and receives two 0-bits. This indicates that both 1-bits and 0-bits exist as the third bit of the ROM data of the attached devices. 8. The bus master writes a 0-bit. This deselects ROM1 leaving ROM4 as the only device still connected. 9. The bus master reads the remainder of the ROM bits for ROM4 and continues to access the part if desired. This completes the first pass and uniquely identifies one part on the 1-Wire bus. 10. The bus master starts a new ROM search sequence by repeating steps 1 through 7. 11. The bus master writes a 1-bit. This decouples ROM4, leaving only ROM1 still coupled. 12. The bus master reads the remainder of the ROM bits for ROM1 and communicates to the underlying logic if desired. This completes the second ROM search pass, in which another of the ROMs was found. 13. The bus master starts a new ROM search by repeating steps 1 through 3. 14. The bus master writes a 1-bit. This deselects ROM1 and ROM4 for the remainder of this search pass, leaving only ROM2 and ROM3 coupled to the system. Note the following: The bus master learns the unique ID number (ROM data pattern) of one 1-Wire device on each ROM Search operation. The time required to derive the part's unique ROM code is: 960 s + (8 + 3 x 64) 61 s = 13.16 ms The bus master is therefore capable of identifying 75 different 1-Wire devices per second. I/O SIGNALING The DS1820 requires strict protocols to insure data integrity. The protocol consists of several types of signaling on one line: reset pulse, presence pulse, write 0, write 1, read 0, and read 1. All of these signals, with the exception of the presence pulse, are initiated by the bus master. The initialization sequence required to begin any communication with the DS1820 is shown in Figure 11. A reset pulse followed by a presence pulse indicates the DS1820 is ready to send or receive data given the correct ROM command and memory function command. The bus master transmits (TX) a reset pulse (a low signal for a minimum of 480 s). The bus master then releases the line and goes into a receive mode (RX). The 1-Wire bus is pulled to a high state via the 5K pull-up resistor . After detecting the rising edge on the 030598 11/27 DS1820 I/O pin, the DS1820 waits 15-60 s and then transmits the presence pulse (a low signal for 60-240 s). Write Scratchpad [4Eh] This command writes to the scratchpad of the DS1820, starting at address 2. The next two bytes written will be saved in scratchpad memory, at address locations 2 and 3. Writing may be terminated at any point by issuing a reset. MEMORY COMMAND FUNCTIONS The following command protocols are summarized in Table 2, and by the flowchart of Figure 10. 030598 12/27 DS1820 MEMORY FUNCTIONS FLOW CHART Figure 10 MASTER TX MEMORY OR CONTROL COMMAND 4Eh WRITE SCRATCHPAD ? Y DS1820 SETS ADDRESS COUNTER TO 2 N BEh READ SCRATCHPAD ? Y DS1820 SETS ADDRESS COUNTER TO 0 N MASTER TX DATA BYTE TO SCRATCHPAD MASTER RX DATA FROM SCRATCHPAD MASTER TX RESET ? N Y MASTER TX RESET ? N Y ADDRESS =3 ? N DS1820 INCREMENTS ADDRESS Y ADDRESS =7 ? N DS1820 INCREMENTS ADDRESS Y N MASTER TX RESET ? MASTER RX 8-BIT CRC OF DATA Y MASTER TX RESET ? N MASTER RX "1s" Y DS1820 TX PRESENCE PULSE 030598 13/27 DS1820 MEMORY FUNCTIONS FLOW CHART Figure 10 (cont'd) 48h COPY SCRATCHPAD ? Y N 44h CONVERT TEMPERATURE ? Y N N PARASITE POWER ? Y N PARASITE POWER ? Y MASTER ENABLES STRONG PULLUP FOR 10 ms MASTER ENABLES STRONG PULL-UP MASTER DISABLES STRONG PULLUP DS1820 BEGINS CONVERSION DS1820 CONVERTS TEMPERATURE MASTER DISABLES STRONG PULL-UP MASTER TX RESET ? N Y MASTER TX RESET ? N DEVICE BUSY CONVERTING TEMPERATURE ? Y N NONVOLATILE MEMORY BUSY ? Y N Y MASTER RX "1"s MASTER RX "0"s MASTER RX "1"s MASTER RX "0"s 030598 14/27 DS1820 MEMORY FUNCTIONS FLOW CHART Figure 10 (cont'd) B8h RECALL E2 ? Y DS1820 RECALLS FROM E2 PROM N B4h READ POWER SUPPLY ? Y N MASTER TX RESET ? Y MASTER TX RESET ? N Y N DEVICE BUSY CONVERTING TEMPERATURE ? N Y PARASITE POWERED ? Y MASTER TX RESET ? Y N MASTER RX "1"s MASTER RX "1"s MASTER RX "0"s MASTER RX "0"s 030598 15/27 DS1820 INITIALIZATION PROCEDURE "RESET AND PRESENCE PULSES" Figure 11 Master TX "reset pulse" 480 s minimum 960 s maximum DS1820 waits 15 - 60 s VCC 1-WIRE BUS GND Master RX 480 s minimum DS1820 TX "presence pulse" 60 - 240 s LINE TYPE LEGEND: Bus master active low Both bus master and DS1820 active low DS1820 active low Resistor pull-up DS1820 COMMAND SET Table 2 1-WIRE BUS AFTER ISSUING PROTOCOL INSTRUCTION DESCRIPTION PROTOCOL NOTES TEMPERATURE CONVERSION COMMANDS Convert T Initiates temperature conversion. 44h MEMORY COMMANDS Read Scratchpad Write Scratchpad Reads bytes from scratchpad and reads CRC byte. Writes bytes into scratchpad at addresses 2 and 3 (TH and TL temperature triggers). Copies scratchpad into nonvolatile memory (addresses 2 and 3 only). Recalls values stored in nonvolatile memory into scratchpad (temperature triggers). Signals the mode of DS1820 power supply to the master. BEh 4Eh Copy Scratchpad Recall E2 48h B8h Read Power Supply B4h NOTES: 1. Temperature conversion takes up to 500 ms. After receiving the Convert T protocol, if the part does not receive power from the VDD pin, the I/O line for the DS1820 must be held high for at least 500 ms to provide power during the conversion process. As such, no other activity may take place on the 1-Wire bus for at least this period after a Convert T command has been issued. 2. After receiving the Copy Scratchpad protocol, if the part does not receive power from the VDD pin, the I/O line for the DS1820 must be held high for at least 10 ms to provide power during the copy process. As such, no other activity may take place on the 1-Wire bus for at least this period after a Copy Scratchpad command has been issued. 030598 16/27 DS1820 Read Scratchpad [BEh] This command reads the contents of the scratchpad. Reading will commence at byte 0, and will continue through the scratchpad until the 9th (byte-8, CRC) byte is read. If not all locations are to be read, the master may issue a reset to terminate reading at any time. READ/WRITE TIME SLOTS DS1820 data is read and written through the use of time slots to manipulate bits and a command word to specify the transaction. Write Time Slots A write time slot is initiated when the host pulls the data line from a high logic level to a low logic level. There are two types of write time slots: Write One time slots and Write Zero time slots. All write time slots must be a minimum of 60 s in duration with a minimum of a one s recovery time between individual write cycles. The DS1820 samples the I/O line in a window of 15 s to 60 s after the I/O line falls. If the line is high, a Write One occurs. If the line is low, a Write Zero occurs (see Figure 12). For the host to generate a Write One time slot, the data line must be pulled to a logic low level and then released, allowing the data line to pull up to a high level within 15 s after the start of the write time slot. For the host to generate a Write Zero time slot, the data line must be pulled to a logic low level and remain low for 60 s. Copy Scratchpad [48h] This command copies the scratchpad into the E2 memory of the DS1820, storing the temperature trigger bytes in nonvolatile memory. If the bus master issues read time slots following this command, the DS1820 will output "0" on the bus as long as it is busy copying the scratchpad to E2; it will return a "1" when the copy process is complete. If parasite powered, the bus master has to enable a strong pull-up for at least 10 ms immediately after issuing this command. Convert T [44h] This command begins a temperature conversion. No further data is required. The temperature conversion will be performed and then the DS1820 will remain idle. If the bus master issues read time slots following this command, the DS1820 will output "0" on the bus as long as it is busy making a temperature conversion; it will return a "1" when the temperature conversion is complete. If parasite powered, the bus master has to enable a strong pullup for 500 ms immediately after issuing this command. Read Time Slots The host generates read time slots when data is to be read from the DS1820. A read time slot is initiated when the host pulls the data line from a logic high level to logic low level. The data line must remain at a low logic level for a minimum of one s; output data from the DS1820 is valid for 15 s after the falling edge of the read time slot. The host therefore must stop driving the I/O pin low in order to read its state 15 s from the start of the read slot (see Figure 12). By the end of the read time slot, the I/O pin will pull back high via the external pull-up resistor. All read time slots must be a minimum of 60 s in duration with a minimum of a one s recovery time between individual read slots. Figure 13 shows that the sum of TINIT, TRC, and TSAMPLE must be less than 15 s. Figure 14 shows that system timing margin is maximized by keeping TINIT and TRC as small as possible and by locating the master sample time towards the end of the 15 s period. Recall E2 [B8h] This command recalls the temperature trigger values stored in E2 to the scratchpad. This recall operation happens automatically upon power-up to the DS1820 as well, so valid data is available in the scratchpad as soon as the device has power applied. With every read data time slot issued after this command has been sent, the device will output its temperature converter busy flag "0"=busy, "1"=ready. Read Power Supply [B4h] With every read data time slot issued after this command has been sent to the DS1820, the device will signal its power mode: "0"=parasite power, "1"=external power supply provided. 030598 17/27 DS1820 READ/WRITE TIMING DIAGRAM Figure 12 MASTER WRITE "0" SLOT 60 s MIN MAX 15 s 15 s 30 s MASTER READ "0" SLOT 1 s< tREC < MASTER READ "1" SLOT 1-WIRE BUS GND 15 s LINE TYPE LEGEND: Bus master active low Both bus master and DS1820 active low DS1820 active low Resistor pull-up 030598 18/27 CCC CCCCCCCC CCC CCCCCCCC CCC CCCCCCCC VCC MASTER SAMPLES 15 s 30 s CCC CCC CCC >1 s 15 s >1 s 15 s MIN DS1820 SAMPLES TYP MAX 15 s 30 s MASTER SAMPLES DS1820 DETAILED MASTER READ "1" TIMING Figure 13 VCC 1-WIRE BUS GND TINIT>1 S TRC MASTER SAMPLES VIH OF MASTER 15 s RECOMMENDED MASTER READ "1" TIMING Figure 14 VCC 1-WIRE BUS GND MASTER SAMPLES 15 s VIH OF MASTER TINIT = SMALL TRC = SMALL LINE TYPE LEGEND: Bus master active low Both bus master and DS1820 active low DS1820 active low Resistor pull-up 030598 19/27 DS1820 Related Application Notes The following Application Notes can be applied to the DS1820. These notes can be obtained from the Dallas Semiconductor "Application Note Book", via our website at http://www.dalsemi.com/, or through our faxback service at (214) 450-0441. Application Note 27: "Understanding and Using Cyclic Redundancy Checks with Dallas Semiconductor Touch Memory Product" Application Note 55: "Extending the Contact Range of Touch Memories" Application Note 74: "Reading and Writing Touch Memories via Serial Interfaces" Application Note 104: "Minimalist Temperature Control Demo" Application Note 105: "High Resolution Temperature Measurement with Dallas Direct-to-Direct Temperature Sensors" Application Note 106: "Complex MicroLANs" Application Note 108: "MicroLAN - In the Long Run" Sample 1-Wire subroutines that can be used in conjunction with AN74 can be downloaded from the website or our Anonymous FTP Site. 030598 20/27 DS1820 MEMORY FUNCTION EXAMPLE Table 3 Example: Bus Master initiates temperature conversion, then reads temperature (parasite power assumed). MASTER MODE TX RX TX TX TX TX TX RX TX TX TX RX DATA (LSB FIRST) Reset Presence 55h <64-bit ROM code> 44h Reset Presence 55h <64-bit ROM code> BEh <9 data bytes> COMMENTS Reset pulse (480-960 s). Presence pulse. Issue "Match ROM" command. Issue address for DS1820. Issue "Convert T" command. I/O line is held high for at least 500 ms by bus master to allow conversion to complete. Reset pulse. Presence pulse. Issue "Match ROM" command. Issue address for DS1820. Issue "Read Scratchpad" command. Read entire scratchpad plus CRC; the master now recalculates the CRC of the eight data bytes received from the scratchpad, compares the CRC calculated and the CRC read. If they match, the master continues; if not, this read operation is repeated. Reset Pulse. Presence pulse, done. TX RX Reset Presence 030598 21/27 DS1820 MEMORY FUNCTION EXAMPLE Table 4 Example: Bus Master writes memory (parasite power and only one DS1820 assumed). MASTER MODE TX RX TX TX TX TX RX TX TX RX DATA (LSB FIRST) Reset Presence CCh 4Eh <2 data bytes> Reset Presence CCh BEh <9 data bytes> Reset pulse. Presence pulse. Skip ROM command. Write Scratchpad command. Writes two bytes to scratchpad (TH and TL). Reset pulse. Presence pulse. Skip ROM command. Read Scratchpad command. Read entire scratchpad plus CRC. The master now recalculates the CRC of the eight data bytes received from the scratchpad, compares the CRC and the two other bytes read back from the scratchpad. If data match, the master continues; if not, repeat the sequence. Reset pulse. Presence pulse. Skip ROM command. Copy Scratchpad command; after issuing this command, the master must wait 6 ms for copy operation to complete. Reset pulse. Presence pulse, done. COMMENTS TX RX TX TX TX RX Reset Presence CCh 48h Reset Presence 030598 22/27 DS1820 MEMORY FUNCTION EXAMPLE Table 5 Example: Temperature conversion and interpolation (external power supply and only one DS1820 assumed). MASTER MODE TX TR TX TX RX DATA (LSB FIRST) Reset Presence CCh 44h <1 data byte> Reset pulse. Presence pulse. Skip ROM command. Convert T command. Read busy flag eight times. The master continues reading one byte (or bit) after another until the data is FFh (all bits 1). Reset pulse. Presence pulse. Skip ROM command. Read Scratchpad command. Read entire scratchpad plus CRC. The master now recalculates the CRC of the eight data bytes received from the scratchpad and compares both CRCs. If the CRCs match, the data is valid. The master saves the temperature value and stores the contents of the count register and count per C register as COUNT_REMAIN and COUNT_PER_C, respectively. Reset pulse. Presence pulse, done. CPU calculates temperature as described in the data sheet for higher resolution. COMMENTS TX RX TX TX RX Reset Presence CCh BEh <9 data bytes> TX RX - Reset Presence - 030598 23/27 DS1820 ABSOLUTE MAXIMUM RATINGS* Voltage on Any Pin Relative to Ground Operating Temperature Storage Temperature Soldering Temperature -0.5V to +7.0V -55C to +125C -55C to +125C 260C for 10 seconds * This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operation sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods of time may affect reliability. RECOMMENDED DC OPERATING CONDITIONS PARAMETER Supply Voltage SYMBOL VDD CONDITION I/O Functions 1/2C Accurate Temperature Conversions Data Pin Logic 1 Logic 0 I/O VIH VIL MIN 2.8 4.3 TYP 5.0 MAX 5.5 5.5 V UNITS NOTES 1, 2 -0.5 2.0 -0.3 +5.5 VCC+0.3 +0.8 V V V 2 2, 3 2, 4 DC ELECTRICAL CHARACTERISTICS PARAMETER Thermometer Error SYMBOL tERR CONDITION -0C to +70C -55C to 0C and +70C to +125C Input Logic High Input Logic Low Sink Current Standby Current Active Current Input Load Current VIH VIL IL IQ IDD IL VI/O=0.4V 2.2 -0.3 -4.0 MIN (-55C to +125C; VDD=3.6V to 5.5V) TYP MAX 1/2 UNITS C 1, 9, 10 V V mA 200 1 5 350 1.5 nA mA A 2, 3 2, 4 2 8 5, 6 7 NOTES See Typical Curve 5.5 +0.8 030598 24/27 DS1820 AC ELECTRICAL CHARACTERISTICS: PARAMETER Temperature Conversion Time Time Slot Recovery Time Write 0 Low Time Write 1 Low Time Read Data Valid Reset Time High Reset Time Low Presence Detect High Presence Detect Low Capacitance SYMBOL tCONV tSLOT tREC rLOW0 tLOW1 tRDV tRSTH tRSTL tPDHIGH tPDLOW CIN/OUT 480 480 15 60 60 1 60 1 MIN TYP 200 (-55C to +125C; VDD=3.6V to 5.5V) MAX 500 120 UNITS ms s s 120 15 15 s s s s 4800 60 240 25 s s s pF NOTES NOTES: 1. Temperature conversion will work with 2C accuracy down to VDD = 3.4 volts. 2. All voltages are referenced to ground. 3. Logic one voltages are specified at a source current of 1 mA. 4. Logic zero voltages are specified at a sink current of 4 mA. 5. IDD specified with VCC at 5.0 volts. 6. Active current refers to either temperature conversion or writing to the E2 memory. Writing to E2 memory consumes approximately 200 A for up to 10 ms. 7. Input load is to ground. 8. Standby current specified up to 70C. Standby current typically is 5 A at 125C. 9. See Typical Curve for specification limits outside the 0C to 70C range. Thermometer error reflects sensor accuracy as tested during calibration. 10. Typical accuracy curve valid for 4.3V VDD 5.5V. 1-WIRE WRITE ONE TIME SLOT tSLOT tREC START OF NEXT CYCLE tLOW1 030598 25/27 DS1820 1-WIRE WRITE ZERO TIME SLOT tSLOT tREC START OF NEXT CYCLE tLOW0 1-WIRE READ ZERO TIME SLOT tSLOT tREC START OF NEXT CYCLE tRDV 1-WIRE RESET PULSE RESET PULSE FROM HOST tRSTL tRSTH 1-WIRE PRESENCE DETECT PRESENCE DETECT tPDHIGH tPDLOW 030598 26/27 DS1820 TYPICAL PERFORMANCE CURVE DS1820 DIGITAL TERMOMETER AND THERMOSTAT TEMPERATURE READING ERROR 5 4 3 2 ERROR (deg. C) 1 UPPER LIMIT SPECIFICATION -55 -35 -15 5 25 45 65 85 105 125 TYPICAL ERROR LOWER LIMIT SPECIFICATION -1 -2 -3 TEMPERATURE (deg. C) 030598 27/27 |
Price & Availability of DS1820
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |